Chromatographe HPLC Alliance iS

Gallery and technical drawings

Description

Key features

• Utilisation simple et intuitive pour tout utilisateur
• Réduction des erreurs courantes
• Accélération du processus décisionnel
• Disponibilité maximale
• Migration aisée des méthodes
• Fiabilité en matière de conformité

Technical specifications

F

1 508 872 1990

T

1 508 478 2000

Depth

63.5 cm (24.99 in.)

Drift

≤100 μAU/hour

Width

49.9 cm (19.64 in.)

Height

74.2 cm (29.23 in.)

Weight

72.5 kg (160.0 lbs.)

Priming

Wet priming can run at flow rates up to 10 mL/min

Bandwidth

<5 nm

Cycle time

≤30 s inject-to-inject

Cell volume

16.3 μL (analytical cell)

Path length

10 mm (analytical cell)

pH range†

1 to 13

Check valves

Passive check valves

Light source

Deuterium arc lamp, warranty 2000 hours or one year (whichever comes first)

Linearity†

≥0.999 R2, for all injection volumes between 2% and 100% of the maximum

Precision†

<1.0% RSD from 0.5 to 0.9 μL

Sampling rate

1, 2, 5, 10, 40, 80, 160 Hz (single channel)

Thermal drift

≤100 μAU/C

Communications

Ethernet

Line frequency

50 to 60 Hz

Pressure limit

1000 psi (analytical cell)

Pump seal wash

Standard

Column capacity

Single column, up to 8.0 mm I.D.; up to 300 mm length with filter or guard column

Column tracking

eConnect™ Technology tracks column usage and history

Sample capacity

1,152 (3x 384-well plate) or 174 (2-mL vials)

Flow accuracy†

±1.0% from 0.2 to 5.0 mL/min

Flow cell design

TaperSlit™ Flow Cell

Sample carryover

≤0.002% caffeine

Solvent capacity

Blend up to four solvents in any combination (standard)

Wavelength range

190 to 700 nm

Wetted materials

316 Stainless Steel, Fluoropolymer, fused silica, PEEK

Flow precision†

≤0.04 min SD, for retention times <26.667 minutes;

Gradient profiles

11 gradient curves [including linear, step (2), concave (4), and convex (4)]

Power consumption

775 VA

Event input/output

Contact closure and/or TTL input/output

Gradient formation

Low-pressure mixing, quaternary gradient

Power requirements

100 to 240 VAC

Wavelength accuracy

±1.0 nm (via Erbium filter)

Solvent conditioning

Passive pre-heating

Temperature accuracy

±0.5 °C at the sensor

Unattended operation

Leak sensors and safe leak handling, full 96-hour diagnostic data display

Accuracy (aspiration)

±0.2 μL

Composition ripple†

≤0.5 mAU over a 10-s window

Gradient delay volume

≤1100 μL

Injection needle wash

Integral, active, and programmable

Temperature stability

±1 °C at the sensor

Injection volume range

0.1 to 100.0 μL as standard

Composition accuracy†

±0.5% absolute (full scale) from 5 to 95%; 0.5 to 5.0 mL/min

Maximum operating range

10,000 psi up to 5.000 mL/min, linearly decreasing to 4000 psi at 10 mL/min

Minimum sample required

3 μL residual, using total recovery 2-mL vials

Quantum synchronization

Injection synchronization between pump and injector enhances

Column compartment temp.

4.0 (or 15.0 °C below ambient, whichever is greater) to 90.0 °C, settable in 0.1 °C increments

Composition precision†

≤0.04 min SD, for retention times <26.667 minutes;

Operating humidity range

20% to 80%, non-condensing

Primary wetted materials

316L stainless steel, gold plated stainless steel, polyimide, PEEK blend, DLC, MP35N

Sample compartment temp.

4.0–40.0 °C, settable in 0.1 °C increments

Wavelength repeatability

±0.1 nm

Informatics compatibility

Empower™ Chromatography Data System (CDS)

Operating flow rate range

0.001 to 10.000 mL/min, in 0.001-mL increments

Any three of the following

48-position, 2.00-mL vial holder

Integrated leak management

Leak sensors, as standard, and safe leak handling

Performance Specifications

1

Dwell volume (total system)

≤1600 μL

Linearity and Dynamic range

r2 ≥0.999 from 0.0001 to 2 AU, ≤5% deviation up to 2.5 AU

Operating temperature range

4.0 to 40.0 °C

Compressibility compensation

Automatic and continuous

Acoustic noise [total system]

≤55 dBA

Volume de séjour (système total)

≤1600 µLVolume de retard de gradient : ≤1100 µLGestion intégrée des fuites : Capteurs de fuite, en standard, et gestion sécurisée des fuitesSynchronisation quantique : La synchronisation d’injection entre la pompe et l’injecteur améliore la reproductibilité du temps de rétentionPlage de débit de fonctionnement : 0,001 à 10,000 mL/min, par incréments de 0,001 mLPlage de fonctionnement maximale : 10 000 psi jusqu’à 5 000 ml/min, diminuant linéairement jusqu’à 4 000 psi à 10 ml/minPlage de pH : 1 à 13Fonctionnement sans surveillance : capteurs de fuite et gestion sûre des fuites, affichage complet des données de diagnostic sur 96 heures via le logiciel de la consoleTemps de cycle : ≤30 s d’injection à injection

Baseline noise (dry), dual wavelength

≤35 μAU

Alliance iS HPLC System Specification Sheet

3

©2023 Waters Corporation. Produced in the U.S.A. April 2023 720007867EN IH-PDF

waters.com

Applications

• Pharmaceutique
• Clinique
• Académique & Recherche
• Industriel
• Environnement